Documentation for 3.10
Files written by the System Under Test
Monitoring files that are created, edited and deleted by the tests
By default, the standard output of the system under test will
be collected to a file called output.<app> and the
standard error will be collected to a file called errors.<app>
(see the guide to files and
). Any other files that might be written by the system under test will be ignored.
However, it is possible to tell TextTest to "collate" individual files
and compare them in a similar way to how it compares standard output and standard error.
It is also possible to tell it to create an additional file which will list all files that were created, edited
or deleted by the system under test (a "catalogue" file), in case comparing every single file is overkill.
This can be done by specifying the config file entry
“collate_file”. This entry is a dictionary and so
takes the following form :
where <source_file_path> is some file your application
writes and <texttest_name> is what you want it to be
called by TextTest.
If you plan to do this, make sure you read the document
describing how the TextTest temporary directory works
<source_file_path> here should in principle never be an
absolute path : it should be relative (implicitly to the
temporary directory described above). This is because your tests
will otherwise have global side effects – making them
harder to understand and more prone to occasional failure,
particularly if run more than once simultaneously.
Note that this ordering can seem counter-intuitive, in effect
you are asking TextTest to copy the text file located at
<source_file_path> to <texttest_name>.<app> in
the temporary directory of that test
where it will be picked up and compared. You might expect the
source to be named before the target, but many different config
dictionary entries use these TextTest names for result files as
keys so this one works the same for consistency.
Standard UNIX file pattern matching is allowed in both
<texttest_name> and <source_file_path>. Where this
is used in the path to the source file it simply means that the
exact name of the file that will be produced may vary, but
whatever file matches the pattern will be copied and given the
same name each time by TextTest, provided it was created or
modified by the test run (unchanged files will not be collected
in this way).
If comparison of a collected file is not desired for any
reason, it can be added to the config file list entry
“discard_file”. The most common usage of this is to
disable the collection of standard output and/or standard error
(i.e. by adding “errors” or “output” to
If the file is not plain-text or needs to be pre-processed
before it can easily be compared, you can tell TextTest to run
an arbitrary script on the file. This script should take a
single argument (the file name to read) and should write its
output to the standard output. You do this by specifying the
composite dictionary entry “collate_script”, which
has the same form as “collate_file” except the value
should be the name of the script to run. The script should be
placed somewhere on your PATH or identified via an absolute
When patterns are used in the TextTest name it means that all
previously saved files that match this “target pattern”
and all files written by the test that match the “source
pattern” become collated files. E.g. suppose we have the
following entry in the config file:
Suppose also that an earlier saved run had produced data1.<app>
and data2.<app> and the latest run produced data1.dump and
data3.dump. Then the list of collated files becomes: data1,
data2, data3. This means that the latest run's data1 will be
compared against the file saved in data1.<app>, data2 will
be flagged as missing and data3 flagged as new result.
Some care is required in writing collate patterns. Completely
general patters like “*:* “ would cause confusion
since anything could relate to anything, in theory. The current
implementation assumes that files have a common stem, i.e.: it
can handle stems like the example above, but not unrelated stems
like “*good* : *bad*”
Binary files should be identified as such by listing them
in the “binary_file” config file entry - this ensures that TextTest will check
whether they are identical but no attempt will be made to filter them or run a difference tool on them.
If they differ, it's then up to the user to examine both files using whatever tools they have available to them.
If standard results have not already been collected for a
particular file produced when a test is run (as they won't be when you've just enabled the mechanism above)
, the file is reported under “New Files” and should be checked
carefully by hand and saved if correct. New files appearing is
also sufficient reason to fail a test, so every test should fail
the first time unless the expected results are imported
externally. The standard output and standard error are also treated this way.
In the same way, if files are not produced that are present
and expected in the standard results, these will be reported
under “Missing Files” and the test will fail.
Saving such a result will cause the missing files to be removed
from the standard results.
Sometimes a system will potentially create and remove a great
many files in a directory structure (TextTest itself is one
example!) Collecting and comparing every single file might be
overkill. Instead, you have the possibility to create a
catalogue file, which will essentially compare which files
(under the test's temporary directory
are present before and after the test has run, and which files
and directories that were present before have been edited during
the test run.
It will then report what has been created, what has been
removed and what has been edited. This is done by setting the
config file entry “create_catalogues” to true. It
will generate result files called catalogue.<app>.
If no differences are found, this is noted briefly at the top of
the file : catalogue files are always created from version 3.6
Note that this feature can be used to aid test
In addition, you can request that the catalogue functionality
checks for processes that were created (leaked!) by the test. If
such processes are found to exist, they will be reported to the
catalogue file and automatically terminated by TextTest. This is
done by getting the SUT to log when it creates a process in a
predictable way. The text identifying the process created should
be provided in the “catalogue_process_string” config
file entry. TextTest will then search the result file indicated
by “log_file” for matches with this string, and
assume the process ID immediately follows it. If the process is
found to be running, it will be reported to the catalogue file
This is controlled by the dictionary entry
“failure_severity”, and takes the form:
<severity> here is a number, where 1 is the most severe
and increasing the number means decreasing the severity. If the
entry is not present, both “output” and “errors”
files will be given severity 1, while everything else will have
The severity has two effects on how TextTest behaves:
- When multiple files are found to be different, the
difference is always reported in the dynamic GUI “details”
column as a difference in the most “severe” file
found to be different.
- If a severity 1 file is found to be different, the whole
line will turn red, otherwise only the “details”
column will turn red.
As an example, the test below has failed in “performance”,
which is a severity 2 file. If the output had also been
different, the whole line on the left would be red and the
details would report “output different(+)”.